SEBS弹性体增韧改性PE-HD/PS共混物及其相容性研究

doi:10.19491/j.issn.1001-9278.2018.12.006

中国塑料 ›› 2018, Vol. 32 ›› Issue (12): 34-40,68.DOI: 10.19491/j.issn.1001-9278.2018.12.006

SEBS弹性体增韧改性PE-HD/PS共混物及其相容性研究

张博文¹，刘喜军^1,2*，付祥明¹，马祥冉¹

1．齐齐哈尔大学材料科学与工程学院 2．黑龙江省教育厅复合改性材料重点实验室

收稿日期:2018-08-04 修回日期:2018-09-01 出版日期:2018-12-26 发布日期:2019-01-25

Study on Toughening and Compatibilizing Effect of SEBS Elastomer on PE-HD/PS Blends

Received:2018-08-04 Revised:2018-09-01 Online:2018-12-26 Published:2019-01-25
Contact: Xijun LIU E-mail:liuxijun2002@126.com；liuxijun2002@163.com

摘要/Abstract

摘要： 采用聚苯乙烯嵌段聚（乙烯亚丁基）嵌段聚苯乙烯（SEBS）弹性体增韧改性高密度聚乙烯（PE-HD）/聚苯乙烯（PS）共混物，通过哈克转矩流变仪制备了PE-HD/PS/SEBS三元共混物，采用扫描电子显微镜（SEM）、旋转流变仪、冲击试验机、热重分析仪（TG）和差式扫描量热仪（DSC）等手段研究了PE-HD/PS/SEBS共混体系的相容性。结果表明，SEBS对共混体系具有良好的增容作用，但当SEBS添加量大于8 %(质量分数，下同)后，部分SEBS出现团聚现象，导致共混体系相容性降低；SEBS的引入对共混物的耐热性影响不大，共混物中连续相PE-HD的熔点稍有降低；随着SEBS添加量的增加，共混物的悬臂梁缺口冲击强度大幅提高。

Abstract: The high-density polyethylene (PE-HD)/polystyrene (PS) blends were prepared by a HAAKE torque rheometer using poly(styrene-b-ethylene-butylene-b-styrene) (SEBS) elastomer as an impact modifier, and the compatibilizing effect of SEBS on this blending system was investigated by a scanning electron microscope, rotary rheometer, impact tester, thermogravimetric analyzer and differential scanning calorimeter. The results confirmed an effective compatibilizing effect of SEBS on the blending system. However, the aggregation was observed when the SEBS content was higher than 8 wt %, which led to a decrease in compatibility of the blending system. There is also no influence on the heat resistance of the blends from SEBS, whereas the melting point of PE-HD phase decreased slightly due to the introduction of SEBS. The notched Izod impact strength was improved significantly with an increase of SEBS content.

张博文刘喜军付祥明马祥冉. SEBS弹性体增韧改性PE-HD/PS共混物及其相容性研究[J]. 中国塑料, 2018, 32(12): 34-40,68.

参考文献

[1] 武壮,张春祥,应良日,等. 聚苯乙烯/高密度聚乙烯复合材料相容性改善方法综述[J]. 广东化工, 2016, 43(22): 105-106.
Wu Zhuang, Zhang Chunxiang, Ying Liangri, et al. Review on Compatibility Improvement of Polystyrene/High Density Polyethylene Composites[J]. Guangdong Chemical Industry, 2016, 43(22): 105-106.
[2] 谢文炳,王玮,茅芸,等. 聚苯乙烯/聚乙烯共混物的力学和流变性能[J]. 石油化工, 1998, 27(3): 176-182.
Xie Wenbing,Wang Wei,Mao Yun, et al. Stuty on the Mechanical and Rheological Propertiesof Polystyrene /Polyethylene Blends[J]. Petrochemical Technology, 1998, 27(3): 176-182.
[3] Sahnoune F.,Cuesta J.-M.-Lopez,Crespy A.. Improvement of the mechanical properties of an HDPE/PS blend by compatibilization and incorporation of CaCO3[J]. POLYMER ENGINEERING AND SCIENCE, 2003, 43(3): 647-660.
[4] A. k. gupta,S. n. purwar. Studies on binary and ternary blends of polypropylene with SEBS, PS, and HDPE. II. Tensile and impact properties[J]. Journal of Applied Polymer Science, 1985, 30(5): 1799-1814.
[5] 孙彤彤. 用ES共聚物对PE-PS共混物增容的研究[J]. 国外塑料, 2000, 18(2): 23-26, 48.
Sun Tongtong. Compatibilizing PE-PS blends with ethylene-styrene copolymers[J]. World Plastics, 2000, 18(2): 23-26, 48.
[6] 孙星星,刘喜军,娄春华,等. sPS/PBA-aPS共混体系的相容性及分散性研究[J]. 中国塑料, 2016, 30(4): 61-68.
Sun Xingxing, Liu Xijun, Lou Chunhual, et al. Studies on Compatibility and Dispersibility of sPS/PBA-aPS Blend[J]. China Plastics, 2016, 30(4): 61-68.
[7] 彭怀炳,刘喜军. MXD6/PA6/EPT共混物力学性能与形态结构研究[J]. 塑料科技, 2015, 43(7): 30-35.
Peng Huaibing,Liu Xijun. Study on Mechanical Properties and Morphology of MXD6/PA6/EPT Blends[J]. Plastics Science and Technology, 2015, 43(7): 30-35.
[8] 孙星星,刘喜军,娄春华,等. sPS/PBA-aPS共混物的力学性能与形态结构研究[J]. 功能材料, 2016, 47(2): 2089-2093.
Sun Xingxing,Liu Xijun,Lou Chunhua, et al. Study on mechanical properties and morphological structure of sPS/PBA-aPS blends[J]. Functional Materials, 2016, 47(2): 2089-2093.
[9] Ruiqi chen,Xueliang jiang,Feng you,et al. Optimizing the morphology, mechanical and crystal properties of in-situ polypropylene/polystyrene blends by reactive extrusion[J]. Fibers and Polymers, 2016, 17(10): 1550-1557.
[10] Leila latreche,Nacereddine haddaoui,Maria esperanza cagiao. The effect of various compatibilizers on thermal, mechanical, and morphological properties of polystyrene/polypropylene blends[J]. Russian Journal of Applied Chemistry, 2016, 89(10): 1713-1721.
[11] Jyotishkumar parameswaranpillai,Seno jose,Suchart siengchin,et al. Phase morphology, mechanical, dynamic mechanical, crystallization, and thermal degradation properties of PP and PP/PS blends modified with SEBS elastomer[J]. Int J Plast Technol, 2017, 21(1): 79-95.
[12] 王雅珍,敖琳,岳成娥,等. PP/TiO2复合材料老化前后动态流变性能研究[J]. 工程塑料应用, 2014, 42(8): 15-20.
Wang Yazhen, Ao Lin, Yue Chenge, et al. Study on Dynamic Rheology Properties of PP/TiO2 Blends Before and A fter Aging[J]. Engineering Plastics Application, 2014, 42(8): 15-20.
[13] 马立群,董少波,石佳,等. 利用废旧聚丙烯腈纤维织物制备聚丙烯用抗老化剂[J]. 中国塑料, 2017, 31(3): 82-89.
Ma Liqun,Dong Shaobo,Shi Jia, et al. Preparation of an Anti-aging Agent for Polypropylene by Waste Polyacrylonitrile Fabrics [J]. China Plastics, 2017, 31(3): 82-89.

SEBS弹性体增韧改性PE-HD/PS共混物及其相容性研究

Study on Toughening and Compatibilizing Effect of SEBS Elastomer on PE-HD/PS Blends

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 0

编辑推荐

Metrics

本文评价