PLA/PPC/OMMT纳米复合材料的结构与性能研究

doi:10.19491/j.issn.1001-9278.2018.02.008

中国塑料 ›› 2018, Vol. 32 ›› Issue (02): 49-56.DOI: 10.19491/j.issn.1001-9278.2018.02.008

PLA/PPC/OMMT纳米复合材料的结构与性能研究

王翔宇¹,赛华捷¹,张玉霞²,王富玉²

1. 北京工商大学，材料与机械工程学院
2. 北京工商大学

收稿日期:2017-12-29 修回日期:2017-10-10 出版日期:2018-02-26 发布日期:2018-02-26

Phase Morphology and Properties of Ternary PLA/PPC/OMMT Nanocomposties

Received:2017-12-29 Revised:2017-10-10 Online:2018-02-26 Published:2018-02-26

摘要/Abstract

摘要： 采用双螺杆挤出机制备了聚乳酸（PLA）/聚碳酸亚丙酯（PPC）共混物和PLA/PPC/有机改性蒙脱土（OMMT）纳米复合材料，采用偏光显微镜、差示扫描量热仪和力学性能试验机等对共混物和纳米复合材料的相态结构、熔融与结晶行为和力学性能等进行了研究。结果表明，在PPC含量低于30 %时，随着PPC含量的增加，PLA/PPC和PLA/PPC/OMMT体系中PLA的玻璃化转变温度（Tg）均降低，在PPC含量为50 %时出现了明显的相分离；随着PPC含量的增加，PLA/PPC的冲击强度增大；OMMT的含量小于1.5 %时，PLA/PPC/OMMT体系的结晶度、拉伸强度、断裂伸长率和冲击强度均随OMMT含量的增加而增大。

Abstract: PLA/PPC blends and PLA/PPC/OMMT(organically modified layered silicate) nanocomposites were prepared by melt mixing in a co-rotating twin-screw extruder. Phase morphology, thermal behavior, and mechanical properties of the resultant PLA/PPC blends and PLA/PPC/OMMT nanocomposites were analyzed by polarizing optical microscope, differential scanning calorimetry and universal testing machine equipments, respectively. The results showed that there were two Tg occurred between PLA and PPC, when the loadings of PPC are equal to and more than 30 wt %, which suggests that the compatibility of PLA and PPC becomes worse, and phase separation occurred obviously at the loading of 50 wt % PPC. With the increasing loadings of PPC, the elongation at break of PLA/PPC blends went up. When the mass fractions of OMMT were less than 1.5 wt %,the crystallinity, tensile strength, elongation at break and impact strength of the nanocomposites all increased.

中图分类号:

TQ327.8

王翔宇赛华捷张玉霞王富玉. PLA/PPC/OMMT纳米复合材料的结构与性能研究[J]. 中国塑料, 2018, 32(02): 49-56.

参考文献

[1]RHIM J W，HONG S I, Ha CS.Tensile,water vapor barrier and antimicrobial properties of PLAnanoclay composite films[J].LWT - Food Sci Technol, 2009, 42(2):612-617 [2]LIM L T, AURAS R, ROBINO M.Processing Technologies for Poly(lactic acid)[J].Progress in Polymer Science, 2008, 33(8):820-852 [3]PETERSSON L, OKSMAN K.Biopolymer based nanocomposites: Comparing layered silicates and microcrystalline cellulose as nanoreinforcement[J].Composites Science & Technology, 2006, 66(13):2187-2196 [4]NIEDDU E, MAZZUCCO L, GENTILE P, et al.Preparation and biodegradation of clay composites of PLA[J].React & Funct Polym, 2009, 69(9):371-379 [5] ZAIDI L, KACI M, BRUZAUD S, et al.Effect of natural weather on the structure and properties of polylactide/Cloisite 30B nanocomposites. Polym Degrad Stabil, 2010, 95: 1751-1758. [6]WANG X, LIU W, LI H, et al.Study on the effect of dispersion phase morphology on porous structure of poly (lactic acid)poly (ethylene terephthalate glycol-modified) blending foams[J].Polymer, 2011, 54(21):5839-5851 [7]MATUANA L M.Solid State Microcellular Foamed Poly (lactic acid): Morphology and Property Characterization[J].Bioresource Technol, 2008, 99(9):3643-3650 [8]REN J.Biodegrable Poly (Lactic Acid)-Synthesis, Modification, Processing and Applications. Beijing: Qinghua University Press, 2011: 38. [9] LI H, ZHANG J W.Research progress in toughening modification of poly(lactic acid).Journal of Polymer Science Part B Polymer Physics, 2011, 49（15）, 1051?1083. [10]VILAY V，MARIATTI M，AHMAD Z.et al[J].Characterization of the mechanical and thermal properties and morphological behavior of biodegradable poly(L-lactide)poly(ε-caprolactone) and poly(L-lactide)poly(butylene succinate-co-L-lactate) polymeric blends. Journal of Applied Polymer Science, 2009, 114(3):1784-1792 [11]LIU H, CHEN, F, LIU, B.et al[J].Super Toughened Poly(lactic acid) Ternary Blends by Simultaneous Dynamic Vulcanization and Interfacial Compatibilization .Macromolecules, 2010, 43(14):6058-6066 [12] RATHI S, CHEN X, COUGHLIN E, et al.Toughening Semicrystalline Poly(lactic acid) by Morphology Alteration.Polymer, 2011, 52（19）, 4184?4188. [13]BREITENBACH A， KISSEL， T.Biodegradable comb polyesters: part II Erosion and release properties of poly(vinyl alcohol)-g-poly(lactic-co-glycolic acid).Polymer 2000, 41（13）, 4781?4792. [14] KIMURA Y, MATSUZAKI Y， YAMANE J, et al.Preparation of block copoly(ester-ether) comprising poly(l-lactide) and poly(oxypropylene) and degradation of its fibre in vitro and in vivo.Polymer, 1989, 30（7）, 1342?1349. [15] YAMAOKA T, TAKAHASHI Y, OHTA T, et al.Synthesis and properties of multiblock copolymers consisting of poly(L-lactic acid) and poly(oxypropylene- co-oxyethylene) prepared by direct polycondensation. J. Polym. Sci., Polym. Chem., 1999, 37（10）, 1513?1522. [16] CHEN C, CHUEH J, TSENG H, ET AL.Preparation and Characterization of Biodegradable PLA Polymeric Blends. Biomaterials, 2003, 24（7）, 1167?1173. [17] CHEN G, KIM H, KIM E, et al.Compatibilization-like effect of reactive organoclay on poly(L-lactide)/(butylene succinate)blends. Polymer 2005, 46（2005）, 11829?11836. [18]OKSMAN K, SKRIFVARS M, SELIN J.Natural fibres as reinforcement in polylactic acid (PLA) composites[J].Composites Science and Technology, 2003, 63(9):1317-1324 [19]YEH J T, TSOU C H, HUANG C Y, et al.Compatible and Crystallization Properties of Poly(lactic acid)Poly(butylene adipate-co-terephthalate) Blends[J].Journal of Applied Polymer Science, 2010, 116(2):680-687 [20]JIANG L, WOLCOTT M, ZHANG J.Study of Biodegradable PolylactidePoly(butylene adipate-co-terephthalate) Blends[J].Biomacromolecules, 2006, 7(1):199- [21]QUERO E, MüLLER A, SIGNORI F, et al.Isothermal Cold-Crystallization of PLAPBAT Blends With and Without the Addition of Acetyl Tributyl Citrate[J].Macromolecular Chemistry & Physics, 2012, 213(1):36-48 [22] LI K, PENG J, TURNG L S, et al.Dynamic Rheological Behavior and Morphology of Polylactide/Poly(butylenes adipate-co-terephthalate) Blends with Various Composition Ratios. Advances in Polymer Technology, 2011; 30(2), 150–157. [23]FUKUSHIMA K, ABBATE C, TABUANI D, et al.Biodegradation of poly (lactic acid) and its nanocomposites[J].Polymer Degradation & Stability, 2009, 94(10):1646-1655 [24] OKAMOTO M.Biodegradable Polymer/Layered Silicate Nanocomposites: A Review, in: Surya Mallapragada, Balaji Narasimhan (Ed.), Handbook of Biodegradable Polymeric Materials and Their Application. Surya Mallapragada and Balaji Narasimahn; 2005: 1-45. [25]MARRAS S I, ZUBURTIKUDIS I, PANAYIOTOU C.Nanostructure vs[J].microstructure: Morphological and thermomechanical characterization of poly (L-lactic acid)layered silicate hybrids. Eur Polym J, 2007, 43(6):2191-2206 [26]RAY S S, YAMADA K, OKAMOTO M, et al.New polylactidelayered silicate nanocomposites[J].Designing of materials with desired properties.Polymer, 2003, 44(21):6633-6646 [27]PLUTA M, JESZKA J K, BOITEUX G.Polylactidemontmorillonite nanocomposites: Structure,dielectric,viscoelastic and thermal properties[J].Eur Polym J, 2007, 43(7):2819-2835 [28]LEE J H, PARK T G, PARK H S, et al.Thermal and Mechanical Characteristics of Poly(l-lactic acid) Nanocomposite Scaffold[J].Biomater, 2003, 24(16):2773-2778 [29]YU Z Y, YIN J B, YAN S F, et al.Biodegradable Poly (L-lactide)Poly(3-caprolactone)-modified Montmorillonite Nanocomposites: Preparation and Characterization[J].Polymer, 2007, 48(21):6439-6447 [30]NAJAFI N, HEUZEY C M, CARREAU J P et al.Control of Thermal Degradation of Polylactide (PLA)-clay Nanocomposites Using Chain Extenders[J].Polym Degrad Stabil, 2012, 97(4):554-565 [31]URBANCZYK L, NGOUNDJO F, ALEXANDRE M, et al.Synthesis of PolylactideClay Nanocomposites by In Situ Intercalative Polymerization in Supercritical Carbon Dioxide[J].Eur Polym J, 2009, 45(3):643-648 [32]KOH H C, PARK J S, JEONG M A, et al.Preparation and Gas Permeation Properties of Biodegradable PolymerLayered Silicate Nanocomposite Membranes[J].Desalination, 2008, 233(1):201-209 [33]THELLEN C, ORROTH C, FROIO D, et al.Influence of Montmorillonite Layered Silicate on Plasticized Poly(L-lactide) Blown Films[J].Polymer, 2005, 46(25):11716-11727 [34]ZENKIEWICZ M, RICHERT J, ROZANSKI A.Effect of Blow Moulding Ratio on Barrier Properties of Polylactide Nanocomposite films[J].Polym Test, 2010, 29(2):251-257 [35]RAY S S, YAMADA K, OKAMOTO M, et al.New PolylactideLayered Silicate Nanocomposites[J].High-performance Biodegradable Materials. Chem Mater, 2003, 15(7):1456-1465 [36]SHI X, GAN Z.Preparation and characterization of poly(propylene carbonate)/montmorillonite nanocomposites by solution intercalation.Eur. Polym. J., 2007, 43, 4852?4858. [37]MA X, YU J, WANG N.Compatibility Characterization of Poly(lactic acid)Poly(propylene carbonate) Blends[J].Journal of Polymer Science: Part B: Polymer Physics, 2006, 44(1):94-101 [38] GE X, ZHU Q, MENG Y.Fabrication and Characterization of Biodegradable Poly(propylene Carbonate)/Wood Flour Composites[J].Appl. Polym. Sci. 2006, 99（3）, 782?787. [39] HIROTSU T, KETELAARS A, NAKAYAMA K.Biodegradation of poly(ε-caprolactone)–polycarbonate blend sheets[J]. Polym. Degrad.Stab. 2000, 68（3）, 311?316. [40]LI J, LAI M, LIU J.Effect of poly(propylene carbonate) on the crystallization and melting behavior of poly(β-hydroxybutyrate-co-β-hydroxyvalerate)[J][J].Journal of Applied Polymerence, 2004, 92(4):2514-2521 [41]GAO M, REN Z, YAN S K.An Optical Microscopy Study on the Phase Structure of Poly (L-lactide acid)Poly(propylene carbonate) Blends[J].Journal of Physical Chemistry B, 2012, 116(32):9832-9837 [42] MAIO E D, LANNACE S, SORRENTINO L, et al.Isothermal crystallization in PCL/clay nanocomposites investigated with thermal and rheometric methods[J]. Polymer 45 (2004) 8893–8900. [43]GARLOTTA D.A literature review of poly (lactic acid)[J].Journal of Polymers and the Environment, 2001, 9(2):63-84 [44]SARASUA J R, ARRAIZA A L, BALERDI P, et al.Crystallinity and mechanical properties of optically pure polylactides and their blends[J].Polymer Engineering & Science, 2005, 45(5):745-753 [45]KISTER G, CASSANAS G, VERT M, et al.Vibrational analysis of poly(l-lactic acid)[J].Journal of Raman Spectroscopy, 2010, 26(4):307-311 [46] KAWASHIMA N, OGAWA S, OBUCHI S, et al.Biopolymers polyesters III applications and commercial products. Weinheim: Wiley-VCH Verlag GmbH; 2002. [47] HARTMANN MH.Advances in the commercialization of poly-(lactic acid)[J]. Polym Prepr (Am Chem Soc, Div Polym Chem), 1999; 40(1): 570-1. [48] KISTER G, CASSANAS G, VERT M.Effects of morphology, conformation and configuration on the IR and Ramanspectra of various poly (lactic acid)[J]. Polymer, 1998; 39（2）: 267-73. [49] KISHORE K, VASANTHAKUMARI R.Nucleation parameters for polymer crystallization from non-isothermal thermal analysis[J]. Colloid Polym Sci, 1988; 266（11）: 999-1002. [50] KISHORE K, VASANTHAKUMARI R, PENNINGS A J.Isothermal melting behavior of poly (l-lactic acid)[J]. J Polym Sci Part B: Polym Phys, 1984; 22（4）: 537-42. [51]RAY S S, BOUSMINA M.Biodegradable polymers and their layered silicate nanocomposites: In greening the 21st century materials world[J].Prog Mater Sci, 2005, 50(2005):962-1079 [52]LIU X, WU Q.Non-isothermal crystallization behaviors of polyamide 6/clay nanocomposites[J]. Eur Polym J 2002; 38（7）:1383. [53]TSENG C R, WU J Y, LEE H Y, et al.Corrigendum to “Poly(oxypropylene)-amide grafted polypropylene as novel compatibilizer for PP and PA6 blends”[J].Polymer 2001; 42（2）:713-725.

PLA/PPC/OMMT纳米复合材料的结构与性能研究

Phase Morphology and Properties of Ternary PLA/PPC/OMMT Nanocomposties

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 9

编辑推荐

Metrics

本文评价

[1]	于志省, 李应成, 王洪学, 庞馨蕾, 王宇遥. PA6/PC基激光直接成型材料研究及其立体结构制件制备[J]. 中国塑料, 2022, 36(2): 8-12.
[2]	朱钰婷, 谷琳, 何家隆, 吉华建, 王玉, 朱惠豪, 马玉录, 谢林生. 微纳层叠共挤PP/PA6/CNTs原位微纤复合膜的制备及性能研究[J]. 中国塑料, 2021, 35(10): 1-7.
[3]	帖锐, 吴悠, 韩小龙, 宋佳洁, 王雨辰, 阚春怡, 袁孟举, 靳玉娟. OMMT对PHBV/EVA共混物的改性研究[J]. 中国塑料, 2021, 35(10): 60-67.
[4]	王杨慧, 马玉录, 谢林生, 宋果, 朱惠豪. 高填充改性复合材料导热预测模型的建立及应用[J]. 中国塑料, 2020, 34(7): 49-55.
[5]	杨北京, 杨旭, 苏婧颖, 李海梅. 免喷涂注塑件的成型品质及应用概述[J]. 中国塑料, 2020, 34(6): 118-125.
[6]	吴长庆林祥任冬云张军. 高填充性聚合物/纳米粒子复合材料的流变行为研究进展[J]. 中国塑料, 2018, 32(02): 1-9.
[7]	张晓亮石阳阳宋海峰许戈文黄毅萍. 新型有机蒙脱土的制备及其在聚丙烯改性中的应用[J]. 中国塑料, 2013, 27(06): 81-86 .
[8]	许文娇陆书玉罗丽娟. 废弃环氧模塑料填充聚氯乙烯的研究[J]. 中国塑料, 2010, 24(11): 89-93 .
[9]	李晓燕胡小平戴亚堂李少先. 聚丙烯/海泡石复合材料的等温结晶行为[J]. 中国塑料, 2010, 24(06): 24-27 .