螺杆构型对啮合异向双螺杆流场影响的仿真分析

›› 2023, Vol. 37 ›› Issue (10): 131-138.

螺杆构型对啮合异向双螺杆流场影响的仿真分析

张一明¹,黄志刚²,徐珍¹,程媛媛¹

1. 北京工商大学
2. 北京工商大学材料与机械工程学院

收稿日期:2023-06-13 修回日期:2023-06-19 出版日期:2023-10-26 发布日期:2023-10-26
基金资助:
草莓贮藏过程中聚乳酸包装材料对其保鲜和品质风味影响机制的研究

Simulation analysis of the influence of screw configuration on the flow field of meshing twin screw

Received:2023-06-13 Revised:2023-06-19 Online:2023-10-26 Published:2023-10-26

摘要/Abstract

摘要： 以聚乳酸（PLA）为例，讨论异向双螺杆挤出机3种不同螺杆构型（阴阳转子螺杆头数比分别为2∶2、3∶2、4∶2）下的流道分布规律。依据理论端面曲线方程在Solidworks中创立上述3种不同螺杆构型的三维模型，使用Workbench软件对3种螺杆构型进行网格模型的建立，再使用Polyflow流体仿真软件进行模拟实际流场情况，得到后处理结果，使用后处理分析软件FieldView进行最终结果的分析；研究PLA流体的在不同螺杆构型下的压力、剪切速率以及黏度。同时使用Polystat统计模块对停留时间分布曲线RTD以及分布混合特性进行对比研究。结果表明，在螺杆转速为60 r/min和阳转子螺杆头数一定的条件下，随着阴转子螺杆头数的增加，压力波动减小，剪切作用提高，停留时间增加，分布效果提高，有利于材料的输出和混合。

关键词: 有螺杆挤出机, 异向啮合, 螺杆头数, 数值模拟, 流场分析

Abstract: The flow channel distribution of three different screw configurations was discussed by taking polylactic acid （PLA） in a twin-screw extruder with different directions at ratios of screw heads to rotor of 2∶2， 3∶2， 4∶2. The 3D models for these three screw configurations were established by the SolidWorks software according to a theoretical end curve equation. The mesh models of the three screw configurations were established using the Workbench software， and the actual flow field was simulated using the Polyflow fluid simulation software to obtain the post-processing results. The final result was analyzed by using the FieldView post-processing analysis software. The pressure， shear rate， and viscosity of the PLA fluid were studied under different screw configurations. Meanwhile， the residence time distribution curve and distribution mixing characteristics were compared by using the Polystat statistical module. The results indicated that the pressure fluctuation decreased， the shear effect increased， the residence time increased， and the distribution effect increased with an increase in the number of screw heads of the negative rotor at a screw speed of 60 rpm with the certain number of screw heads of the positive rotor. There are advantageous to the output and mixing of materials.

Key words: screw extruder, opposite meshing, number of screw head, numerical simulation, flow field analysis

张一明黄志刚徐珍程媛媛. 螺杆构型对啮合异向双螺杆流场影响的仿真分析[J]. , 2023, 37(10): 131-138.

参考文献

[1]商嘉玮, 黄志刚, 张一明, 杨亚楠, 代祥基.四螺杆挤出机螺杆排列方式对聚乳酸流场特性的影响[J].食品与机械, 2023, 39(03):72-77 [2] 耿孝正.双螺杆挤出机及其应用[J].中国塑料, 2005(02):73. [3] 范涛, 陈作炳, 杜佳佳, 谢强, 汤帅.螺槽深度对单螺杆挤出机熔融输送段熔融过程的影响[J].塑料工业， [4]15, 43(04):42-47. [5] 张雪晨, 张丽梅, 黄志刚, 刘忠尧, 李贺.啮合同向双螺杆挤出机不同螺杆构型对其流场的影响[J].食品 [6]与机械, 2022, 38(04):99-103+206. [7]. Gangadhar Angadi, Hebbale NarayanaRao Narasimha Murthy, Sridhar Ramakrishna, Salim Firdosh, [8]Raghavendra Nagappa, Krishna Munishamaiah.Effect of screw configuration on the dispersion of nanofillers in the rmoset polymers[J]. Journal of Polymer Engineering, 2017, 37(8).815-825. [9]魏静, 孙旭建, 孙伟等.双螺杆捏合机转子型线设计与数值模拟[J].机械工程学报, 2013, 49(03):63-73 [10] 许国智.粒子示踪法研究胶体悬浮液在复合外场下的动态[D].华南理工大学, 2017. [11]陈龙, 董力群, 张亚军, 范一强.基于的异向双螺杆的参数化设计[J].中国塑料, 2018, 32(01):120-124 [12] 陈大兵.双螺杆捏合机螺杆元件性能分析与实验研究[D].大连理工大学, 2015. [13]王少峰, 张媛, 刘美莲, 等.不同温度状态下啮合异向双螺杆挤出机的流道分布规律[J].食品与机械, 2018, 34(10):71-74 [14]韩海川, 刘谨, 李开国, 等.双螺杆啮合元件与反螺纹元件对流场影响的仿真[J].工程塑料应用, 2020, 48(6):74-77 [15]蒋卫鑫, 黄志刚, 赵玉莲, 等.基于田字形网格食品托盘挤出成型分析[J].食品与机械, 2017, 33(12):86-90 [16]黄志刚, 蒋卫鑫, 李鑫, 等.啮合异向双螺杆挤出机仿真研究[J].包装学报, 2019, 11(3):9-15 [17] 安琪, 黄志刚, 胡淑珍等.适应性网格技术在异向双螺杆挤出机中的仿真[J].食品与机械, 2021, 37(04) [18]:91-97. [19] 赵玉莲, 李鑫, 安琪, 黄志刚.非等温条件下啮合同向双螺杆挤出过程数值模拟分析[J].食品与机械, [20]19, 35(04):76-79. [21]FORMELA K, CYSEWSKA M.Efficiency of thermomechanical reclaiming of ground tire rubber conducted in counter-rotating and co-rotating twin screw extruder[J].Polimery, 2014, 59(3):231-238 [22] 杨明山, 赵明.塑料成型加工工艺设备[M].北京:印刷工业出版社, 2010:14-16. [23] 张先明.挤出过程停留时间分布的实验研究和数值模拟[D].杭州:浙江大学，2008． [24] 陈峰峰, 李浩杰, 王一飞等.基于Polyflow的反螺纹元件对粒子分散性仿真研究[J].工程塑料应用, [25]21, 49(09):82-86.