中国塑料

中国塑料 ›› 2007, Vol. 21 ›› Issue (4): 13-19.

• 材料与性能 • 上一篇    下一篇

PP /PET/EPDM-g-GMA共混物结构与性能研究

许军1,2，姚琲2，朱晨1   

  1. 1.中国民航大学理学院，天津300300; 2.天津大学分析测试中心，天津300072
  • 出版日期:2007-04-26 发布日期:2021-05-07

Study on Structure and Properties of PP/PET/EPDM-g-GMA Blend

XU Jun1, 2，YAO Pei2，ZHU Chen1   

  1. 1. College of Science, Civil Aviation University of China, Tianjin 300300, China
    2. Center for Analysis, Tianjin University, Tianjin 300072, China
  • Online:2007-04-26 Published:2021-05-07

PDF

152

摘要： 通过反应共混制备了PP/PET/EPDM-g-GMA共混物。用扫描电镜和图像处理软件对共混物形貌进行定性和定量分析，用偏光显微镜观察共混物等温结晶形态，最后测量共混物的力学性能。结果表明:在PP/PET共混物中加人EPDM-g-GMA后，两相相容性改善。进一步加人成核剂后分散相尺寸更小、粒径分布更均匀;PP球晶随PET，的混人而减小;在PP,}PET体系中加人EPDM-g-GIvIA起到反应增容和橡胶增韧的协同效应，使缺口冲击强度由未加增容剂时的2.0 kJ/m'-提高至6.6 kJ/m2，弹性模量较PP提高了38 % ; PP/PE〕共混物的拉伸强度随PET含量的增加下降，在相同PET含量的情况下，加人EPDM-g-GMA后，共混物的拉伸强度与未增容体系基本一致。

关键词: 聚丙烯, 聚对苯二甲酸乙二醇醋, 共混, 形貌, 力学性能

Abstract: PP/PET/EPDM-g-GMA blends were prepared via reactive melt blending. The morphology of the blends was analysized using SEM and image processing software, which confirmed that the compatibility of PP and PET was improved by EPDM-g-GMA，Isothermal crystallization of the blends were observed using polarizing microscope, it was found that the dimension and distribution of the spherulites became finer via using nucleating agent. The dimension of PP spherulites decreased with the inclusion of PET.  EPDM-g-GMA not only compatibilized but also toughened the system,  making the impact strength increased from 2 .2kJ/mzto6 .5kJ/m2 and the tensile modulus increased by 38 .6%compared with neat PP. The tensile strength decreased with increasing PET content, YP/PET/EYDM-g-GMA had no obvious effect on this property.

Key words: polypropylene, polyethylene terephthalate, blending, morphology, mechanical property

中图分类号: 

京公网安备11010802034965号　 京ICP备13020181号-2
《中国塑料》编辑部 ©2008-2024 版权所有
地址:北京市海淀区阜成路11号　邮编：100048
编辑部：010-68985541　联系信箱：cp@plaschina.com.cn
广告部/发行部：010-68985253　本系统由北京玛格泰克科技发展有限公司设计开发