工艺条件对PBAT/PLA原位成纤共混体系结构与性能的影响

›› 2023, Vol. 37 ›› Issue (4): 60-66.

工艺条件对PBAT/PLA原位成纤共混体系结构与性能的影响

王富玉¹,郭金强¹,杨超永¹,张玉霞²

1. 北京工商大学
2. 北京工商大学化学与材料工程学院

收稿日期:2023-03-24 修回日期:2023-01-30 出版日期:2023-04-26 发布日期:2023-04-26

Effect of processing conditions on structure and properties of PBAT/PLA in- situ fibrillation blends

Received:2023-03-24 Revised:2023-01-30 Online:2023-04-26 Published:2023-04-26
Contact: Zhang YuXia E-mail:chianplas@126.com

摘要/Abstract

摘要： 将质量比为80/20的PBAT/PLA共混物在单螺杆挤出流延成型机中通过调控工艺条件（口模温度、拉伸速度）直接熔融共混制备PBAT/PLA原位成纤共混薄膜。结果表明，在较低口模温度时，随着拉伸速度的提高，PLA微纤细化程度加大，结晶度先提高后降低，纵向拉伸强度先增加后减小，力学性能各向异性明显。在口模温度为150 ℃、拉伸速度为5.0 m/min时，共混体系中PLA成纤效果最明显；PBAT和PLA的结晶度最高分别为4.8 %和23.7 %；纵向拉伸强度达到29.8，比纯PBAT提高了41 %。

关键词: 聚己二酸/对苯二甲酸丁二醇酯, 聚乳酸, 口模温度, 拉伸速度, 原位成纤

Abstract: Poly（butylene adipate terephthalate）（PBAT）/ poly（lactic acid）（PLA）（PBAT/PLA， 80/20）in-situ fibrillation blends were prepared by a single-screw melt-extrusion casting machine under various die temperature and stretching speed. The results indicated that at lower die temperature， with the increase of stretching speed， the diameter of PLA microfibers dwindles， the crystallinity degree enhance first and then lowers， the longitudinal tensile strength increases first and then decreases， and the mechanical anisotropy is obvious. When the die temperature was 150 ℃ and the stretching speed was 5.0 m/min， the number of dispersed phase PLA microfibers grow； the highest crystallinity of PBAT and PLA are 4.8 % and 23.7 %， respectively； the longitudinal tensile strength reaches the maximum of 29.8 MPa， which is at least 41 % higher than that of pure PBAT.

Key words: poly（butylene adipate terephthalate）, poly（lactic acid）, die temperature, drawing speed, in-situ fibrillation

王富玉郭金强杨超永张玉霞. 工艺条件对PBAT/PLA原位成纤共混体系结构与性能的影响[J]. , 2023, 37(4): 60-66.

参考文献

[1] 周怡凯.PBAT基生物可降解复合材料的增容改性与表征[D].泰安市：山东农业大学，2021. [2]ZHOU YIKAI.Compatibility Modification and Characterization of PBAT-based Biodegradable composites[D]. TAIAN: ShanDong Agricultural Universty, 2021. [3] Ferreira F.V, Mariano M., Lepesqueur L. S. S., et al. Silver nanoparticles coated with dodecanethiol used as fillers in non-cytotoxic and antifungal PBA T surface based on nanocomposites. [J].Materials Science and Engineering, 2019, 98( C)::800-807 [4]Zehetmeyer G.Meira S[J].M. M., Scheibel J. M., et al. Biodegradable and antimicrobial films based on poly (butylene adipate-co-terephthalate) electrospun fibers. Polymer Bulletin, 2016, 74(8):3243-3268 [5] Biundo A, Hromic A, Parkovkeller T, et al.Characterization of a Poly (butylene adipato-co-terephthalate)-hydrolyzing lipase from palominos’ ferments [J]. [J].Applied microbiology and biotechnology., 2015, 96:22-25 [6] 潘燕.原位拉伸聚合物结构与性能研究[D].重庆:重庆理工大学, 2013. [7]PAN YAN.Study on Structure and Properties of Polymer by In-situ Tensile Technology[D]. Chongqing: Chongqing University of Technology, 2013. [8] 张玉霞.可生物降解聚合物及其纳米复合材料[M]. 北京: 机械工业出版社, 2017: 267. [9]王翔宇，张玉霞.纳米复合材料微观结构调控[J].中国塑料, 2020, 34(4):35-41 [10]WANG XIANGYU, ZHANG YUXIA.Tuning of Microstructure of PLAPBATOMMT Nanocomposite[J].CHINA PLASTICS, 2020, 34(4):35-41 [11]赛华捷, 张玉霞.的有机改性及其在中的应用[J].中国塑料, 2019, 33(01):133-146 [12]SAI HUAJIE, ZHANG YUXIA.Organic Modification of MMT and Its Applications in PLA[J].CHINA PLASTICS, 2019, 33(01):133-146 [13] Paul D R.Polymer blends[M]. Elsevier, 2012. [14]张爽，冯钠，刘俊龙等.原位成纤复合材料研究进展[J].橡塑与技术装备, 2005, 12(31):25-30 [15]ZHANG SHUANG, FENG NA, LIU JUNLONG, et al.The Progress of Research on the On-site fiber forming composite materials[J].CHNIA RUBBERPLASTICS TECHNOLOGY AND EQUIPMENT, 2005, 12(31):25-30 [16]Li M F, Xiao R, Sun G.Morphology development and size control of poly (trimethylene terephthalate) nanofibers prepared from poly (trimethylene terephthalate)cellulose acetate butyrate in-situ fibrillar composites[J].Journal of Materials Science, 2011, 46(13):4524-4531 [17]董珈豪，戚远慧，韦良强，等.分散相含量对原位增强复合材料性能的影响[J].中国塑料, 2016, 30(6):57-62 [18]DONG JIAHAO, QI YUANHUI, WEI LIANGQIANG, et al.Effect of Contents of Dispersed Phase on properties of PTTPOE in-situ Fiber Reinforced composite[J].CHINA PLASTICS, 2016, 30(6):57-62 [19] 王国全.聚合物共混改性原理与应用[M]. 中国轻工业出版社，2016, 55-58. [20] 王占杰.原位成纤复合技术改善聚丙烯的加工行为及力学性能[D].青岛：青岛科技及大学，2010. [21]WANG ZHANJIE.Improvement of the Rheological and Mechanical Properties of Polypropylene by In-situ Fibrillation Composite Method[D]. Qingdao: Qingdao University of Technology, 2010. [22] 黄英.三螺杆直接挤出原位成纤机理及微纤复合体系结构与性能的研究[D]. 北京：北京化工大学，2017. [23]HUANG YING.Study the Microfibrils’ Formation Mechanisam and Structure and Properties of In-situ Microfibrillar Composites via direct Extrusion using a Triple-screw Extruder[D]. Bei Jing:Beijing University of Chemical Technology, 2017. [24] 任曙霞.PTT/PE共混及原位微纤材料的制备及性能研究[D]. 上海：东华大学，2010. [25]REN SHUXIA.Study on the Preparation and Properties of PTT/PE Blends and In-situ Microfiber Composites[D]. Shanghai: DONGHUA University, 2010. [26]李忠明，杨鸣波，卢忠远，等.热拉伸比对原位微纤化复合材料形态和拉伸性能的影响[J].复合材料学报, 2005, 22(3):9-15 [27]LI ZHONGMING, YANG MINGBO, LU ZHONGYUAN, et al.Influence of Hot Stretch Ratio on Morphology and Tensile Properties pf Poly (ethylene terephthalate) and Polyethylene Intu Microfibrillar Composite[J].Acta Materiae Compositae Sinica, 2005, 22(3):9-15 [28] 练兴瀚.原位纳纤化PLA基共混材料的制备及其性能研究[D]. 广州市：华南理工大学，2020. LIAN XINGHAN. Study on preparation and properties of in situ nanofibril reinforced PLA based blends[D]. Guangzhou: South China University of Technology, 2020. [29] 孙永锋, 王益龙, 王爱平.HDPE/PA6原位微纤共混物的制备与性能[D].现代塑料加工应用，2013，25（3）：5-8. [30]SUN YONGFENG, WANG YILONG, WANG AIPING.Preparation and Properties of HDPEPA6 in Situ Micro-fibrillar Blend[J].MODERN PLASTIC PROCESSING AND APPLICATIONS, 2013, 25(3):5-8 [31]Yeh J T, Tsou C H, Huang C Y, et al.Compatible and crystallization properties of poly(lactic acid)poly(butylene adipate-co-terephthalate) blends[J].Journal of Applied Polymer Science, 2010, 116(2):680-687 [32]宋敬思，王贤增，周洪福，等.的扩链反应及其微孔发泡行为研究[J].中国塑料, 2018, 32(11):42-48 [33]SONG JINGSI, WANG ZENGXIAN, ZHOU HONGFU, et al.Study on Chain Extension and Microcelluar Foaming Behaviors of Poly( butyleneadipate-co-terephthlate)[J].CHINA PLASTICS, 2018, 32(11):42-48 [34]张声莹，李姜红，赵大江等.原位微纤复合材料的研究进展[J].广州化工, 2016, 44(10):5-8 [35]ZHANG SHENGYING, LI JIANGHOMG, ZHAO DAJIANG, et al.Research Progress on Polymer in-situ Microfiber Composites[J].Guangzhou Chemical Industry, 2016, 44(10):5-8 [36]刘渝，黄安荣，韦良强，等.黏度比对原位微纤复合材料形态及性能的影响[J].塑料工业, 2018, ，46(8):43-46 [37]LIU YU, HUANG ANRONG, WEI LIANGQIANG, et al.The Effect of Viscosity Ratio on the Morphology and Properties of EVA PP In-Situ Microfibillar Composites[J].CHINA PLASTICS INDUSTRY, 2018, 46(8):43-46